A door that rubs on the floor is usually dropped on its hinges, swollen from moisture, or blocked by a threshold or floor that changed height. Start by reading the rub mark and checking the hinges and frame before you sand, plane, or trim anything. If the door is warped, the frame is out of square, or there’s rot or active water damage, stop and call a pro.
Start with the rub mark
The wear pattern usually points to the problem before you touch a tool. A shiny spot at the lower latch corner often means the door has dropped or the frame has shifted. A rub along most of the bottom edge points more toward floor contact, a swollen door, or a threshold that sits too high.
Look at both the door and the floor. If the finish is scuffed only on one corner, the interference is local, not all along the opening. If you see a long scrape line on the floor, that tells you where the door path is hitting as it swings.
Before you start
- Work with the door open and supported so it doesn’t swing unexpectedly while you inspect it.
- Have a screwdriver, a level or straightedge, and a flashlight ready.
- Check whether the rub started after humid weather, a spill, recent painting, new flooring, or a threshold change.
- Stop if the door is swollen, warped, soft, or stained, or if the frame or floor looks like it moved. Those are not clean hinge-adjustment jobs.
Read the gap around the door before you change anything. If the top gap gets tighter toward the latch side, the door may have sagged. If the gap looks even but the bottom edge drags, the threshold or floor may be the real obstacle.
Is the door dropped, swollen, or blocked by the floor?
Use the rub mark, the hinge movement, and the timing of the problem to sort out the cause.
| What you see | Likely cause | Best next check |
|---|---|---|
| Shiny wear at lower latch corner | Dropped door | Check hinge screws and hinge play |
| Rub across most of bottom edge | Floor, threshold, or swelling | Check clearance under the door |
| New rubbing after humidity or water | Swollen door | Let it dry and recheck |
| Door is hard to close and latch | Alignment issue | Check hinges before trimming |
If the door started rubbing after damp weather, a spill, or a leak, moisture may be swelling the door or the subfloor. If it rubs on the same spot every time and the hinges feel loose, the door may have dropped. If the floor or threshold is visibly higher than before, don’t treat this like a door-only problem.
Try the least invasive fix first
- Close the door slowly and watch where it touches. Then open it and lift gently on the handle side. Any movement at the hinges is a clue.
- Check the hinge screws, especially the top hinge. Loose screws are common, and a door can drop enough to scrape even when the latch still lines up. If a screw just spins, the wood behind it may be stripped.
- Tighten the screws before you remove any material. If the door closes cleanly after tightening, you’re done. If it still drags, move on to the hinge fit or the threshold.
- Check the threshold and the floor if the rub is at the bottom edge. A raised threshold, lifted flooring, or a floor that has settled can make a door scrape even when the hinges are fine.
The wrong move is usually cutting the door before confirming that the hinge or frame moved.
When loose hinges are the real cause
If the door has dropped on the latch side, tightening hinge screws is often the first real fix. Tighten the screws in both the door leaf and the jamb side, starting with the top hinge, because that hinge carries a lot of the load. If a screw is stripped, replace it with a longer screw that bites into solid wood, if the hinge and jamb allow that.
If tightening doesn’t pull the door back into place, a hinge shim may help. A shim is a thin spacer placed behind a hinge leaf to change the door’s position a little. On a door that rubs low on the latch side, a shim can move the door just enough to restore clearance without shaving the bottom edge.
Use shims when the hinges are tight but the door still sits slightly low or out of alignment. Use screw tightening when the hardware is loose and the door has visibly dropped. If the hinge screws are solid and the door still drops, the hinge barrels may be worn or the frame may have shifted.
When the bottom edge needs trimming
Trim, plane, or sand the bottom edge only after you’ve ruled out hinge drop and floor contact from a changed threshold. If the door is truly too tall for the opening, the bottom edge is the place to adjust.
A plane removes wood fastest and gives the cleanest edge if you have the tool and the skill to keep the cut straight. Sandpaper is slower and better for tiny corrections or cleanup after planing. Trimming with a saw is for more serious clearance changes, but that step can expose raw wood and can change the look of the door, so it’s not the first choice.
Remove material in small amounts and check often. If you take too much off, the gap may look uneven, the door may no longer cover the opening properly, and you can’t put the wood back.
After any cut, seal the bare edge if the door is wood and the finish was removed. That helps reduce future swelling.
Check the floor, threshold, and moisture source
Sometimes the door is fine and the opening changed. A raised floor covering, a swollen threshold, or a floor that has moved can all create a new rub point. If the scrape starts after a spill, damp weather, or a plumbing leak, moisture may be swelling the door or the subfloor.
Check the threshold first if the door only drags at the very bottom edge near the latch side. Then look for flooring that has lifted, buckled, or been installed too high under the swing path. If the door rubs only in one season, compare it in dry weather and damp weather before you cut it.
If you see swelling, soft wood, staining, or a musty smell, pause. Water damage can make a door swell unevenly and can also mean the frame or floor needs attention before any door repair will hold.
Test the door after each change
After every adjustment, test the door in the same way. Open it fully, close it slowly, and listen for the rub. Then latch it without lifting or pushing hard on the handle. The door should swing freely, clear the floor, and close without binding against the jamb.
Check the gap around the door after the fix. You want a consistent gap and no new scrape marks on the bottom edge or floor. If the latch no longer catches easily, you may have corrected the drag but shifted the alignment too far.
A good repair feels boring. The door moves normally, the latch lines up, and nothing has to be forced.
When to stop and call a pro
Stop if the door is warped enough that no hinge adjustment changes the rub, or if the frame itself looks out of square. Stop too if you find rot, soft wood, active water damage, or a floor that is clearly moving. Those problems can make a simple trim useless or make the damage worse.
You should also pause if the door has been painted shut, the jamb is cracked, or the threshold is loose and pulling away. In those cases, the door rub is often a symptom of a bigger repair. A pro can tell whether the issue is in the door, the frame, or the structure around it before more wood comes off the wrong place.
Conclusion
If the door still rubs after hinge checks, threshold checks, and a careful test, stop before removing more wood and reassess the frame, floor, or moisture problem.
Frequently Asked Questions
Should I sand the bottom of the door first if it rubs?
No. Check the hinges, the rub mark, and the floor first, because a dropped door or raised threshold is often the real cause. Sanding too early can leave you with a door that clears today but sits too high later.
How do I know if hinge screws are the problem?
If the door rubs low on the latch side and the top of the door looks tighter on that side, loose hinge screws are a strong suspect. A little lift at the handle side or visible hinge play also points to a dropped door.
What if the door only rubs when the weather changes?
That usually points to moisture or seasonal swelling. In many cases the door will improve when the air dries out, but you should still check the hinges and threshold so you don’t trim a door that will shrink back later.